Polyurethane protecting coating protection black 0,63l 0RS099
Index: 0RS099
Polyurethane protecting coating protection PROFIRS TRUCK BEDLINER 2K 0RS099 790G, polyurethane 0,63l 0,79kg, intended use: car body, colour black
APPLICATION:
UBS Gun:
Mixing ratio - 3:1
By weight: 790g + 210g
By volume: 630ml + 210ml
Shake the container with the product, unscrew the cap, open the lid, add the hardener. Close with the cap and mix very thoroughly.
Pot life - About 1 h at 20°C
Number of layers - 2 layers.
1 dry layer about 150µm.
First layer - even spray, pressure 2-4 bar until coverage is achieved. Distance from the painted surface about 50cm.
Allow evaporation between layers 30÷50 minutes.
To achieve the desired structure, reduce the pressure and increase the distance from the painted surface.
To ensure the appropriate structure is achieved, apply the second layer using the droplet technique. Distance from the painted surface and pressure change the structure.
Curing time - Touch dry: 1 h/ 20°C
Usable hardness: 3 days/ 20°C
Full hardness (severe conditions): 7 days/ 20°C
Temperature below 20°C significantly extends the curing time.
Drying
To accelerate physical drying, it is recommended to heat at a maximum temperature of 45°C for 50-60 minutes. Before heating, allow evaporation time of 1.5 to 2 hours.
IMPORTANT! The drying process does not accelerate the full curing of the coating. It is recommended to wait 7 days to achieve full hardness (use in severe conditions).
Gravity Gun:
Mixing ratio - 3:1 + 10÷20% TROTON acrylic thinner
By weight: 790g+210g+74÷148g
By volume: 630ml+210ml+ 84÷168ml
Shake the container with the product, unscrew the cap, open the lid, add the hardener. Close with the cap and mix very thoroughly. Add the thinner and mix.
Pot life - about 1 h at 20°C
Number of layers - 2 layers.
1 dry layer about 50µm.
Parameters for gravity gun
Nozzle: 1.4÷2.5 mm; Inlet pressure: 2.0 bar.
First layer - even spray, pressure 2 bar until coverage is achieved. Distance from the painted surface about 40cm.
Allow evaporation between layers 30÷50 minutes.
To achieve the desired structure, reduce the pressure and increase the distance from the painted surface.
To ensure the appropriate structure is achieved, apply the second layer using the droplet technique. Distance from the painted surface and pressure change the structure.
Curing time - Touch dry: 1 h/ 20°C
Usable hardness: 3 days/ 20°C
Full hardness (severe conditions): 7 days/ 20°C
Temperature below 20°C significantly extends the curing time.
Drying
To accelerate physical drying, it is recommended to heat at a maximum temperature of 45°C for 50-60 minutes. Before heating, allow evaporation time of 1.5 to 2 hours.
IMPORTANT! The drying process does not accelerate the full curing of the coating. It is recommended to wait 7 days to achieve full hardness (use in severe conditions).
Information
RANGERS for color
To tint the RANGERS agent, add solvent-based products (to the entire mixture):
Pigment paste - 5÷10%
Acrylic base - 10÷15%
Polyurethane - 10÷15%
Information
RANGERS black/ for color
The coating can be repainted. Wait 24h for the product to dry. Treat the surface with fine Troton abrasive fleece, clean and degrease (Silicone Remover Troton).
Information
Anti-slip additive
To obtain an anti-slip coating, use TROTON RANGERS anti-slip powder (10g).
The package contains 10g of anti-slip additive needed to fill one bottle of RANGERS product (1kg/840ml mixture).
Pour the contents directly into the RANGERS bottle, add the hardener and mix thoroughly for about 2 minutes.
The anti-slip coating can be obtained using a UBS or conventional gun. The anti-slip additive can be added to all layers or to the last layer.
Information
RANGERS black HARDENER
ml g ml g
210 263 70 70
315 395 105 105
630 790 210 210
1260 1580 420 420
1890 2370 630 630
UBS Conventional Gun:
Mixing ratio - 3:1
3:1+10÷20%
Nozzle – 1.4÷2.5 mm
Inlet pressure 2÷4 bar 2 bar
Distance 20÷50 cm 20÷50 cm
Number of layers 2 2
Evaporation between layers 30÷50 minutes 30÷50 minutes
Usable hardness 3 days 3 days
Full hardness (severe conditions) 7 days 7 days
Efficiency 2.5÷3 m2 3.5÷6.5 m2
General notes:
Do not exceed the recommended amount of hardener!
The best results are achieved by painting at room temperature.
The ambient temperature and the temperature of the applied product should be similar.
When working with 2-component products, it is recommended to use personal protective equipment. Protect eyes and respiratory tract.
Rooms should be well ventilated.
Tools should be cleaned immediately after application.
Note: For safety, always follow the instructions in the product's MSDS sheet.
Description
APPLICATION:
UBS Gun:
Mixing ratio - 3:1
By weight: 790g + 210g
By volume: 630ml + 210ml
Shake the container with the product, unscrew the cap, open the lid, add the hardener. Close with the cap and mix very thoroughly.
Pot life - About 1 h at 20°C
Number of layers - 2 layers.
1 dry layer about 150µm.
First layer - even spray, pressure 2-4 bar until coverage is achieved. Distance from the painted surface about 50cm.
Allow evaporation between layers 30÷50 minutes.
To achieve the desired structure, reduce the pressure and increase the distance from the painted surface.
To ensure the appropriate structure is achieved, apply the second layer using the droplet technique. Distance from the painted surface and pressure change the structure.
Curing time - Touch dry: 1 h/ 20°C
Usable hardness: 3 days/ 20°C
Full hardness (severe conditions): 7 days/ 20°C
Temperature below 20°C significantly extends the curing time.
Drying
To accelerate physical drying, it is recommended to heat at a maximum temperature of 45°C for 50-60 minutes. Before heating, allow evaporation time of 1.5 to 2 hours.
IMPORTANT! The drying process does not accelerate the full curing of the coating. It is recommended to wait 7 days to achieve full hardness (use in severe conditions).
Gravity Gun:
Mixing ratio - 3:1 + 10÷20% TROTON acrylic thinner
By weight: 790g+210g+74÷148g
By volume: 630ml+210ml+ 84÷168ml
Shake the container with the product, unscrew the cap, open the lid, add the hardener. Close with the cap and mix very thoroughly. Add the thinner and mix.
Pot life - about 1 h at 20°C
Number of layers - 2 layers.
1 dry layer about 50µm.
Parameters for gravity gun
Nozzle: 1.4÷2.5 mm; Inlet pressure: 2.0 bar.
First layer - even spray, pressure 2 bar until coverage is achieved. Distance from the painted surface about 40cm.
Allow evaporation between layers 30÷50 minutes.
To achieve the desired structure, reduce the pressure and increase the distance from the painted surface.
To ensure the appropriate structure is achieved, apply the second layer using the droplet technique. Distance from the painted surface and pressure change the structure.
Curing time - Touch dry: 1 h/ 20°C
Usable hardness: 3 days/ 20°C
Full hardness (severe conditions): 7 days/ 20°C
Temperature below 20°C significantly extends the curing time.
Drying
To accelerate physical drying, it is recommended to heat at a maximum temperature of 45°C for 50-60 minutes. Before heating, allow evaporation time of 1.5 to 2 hours.
IMPORTANT! The drying process does not accelerate the full curing of the coating. It is recommended to wait 7 days to achieve full hardness (use in severe conditions).
Information
RANGERS for color
To tint the RANGERS agent, add solvent-based products (to the entire mixture):
Pigment paste - 5÷10%
Acrylic base - 10÷15%
Polyurethane - 10÷15%
Information
RANGERS black/ for color
The coating can be repainted. Wait 24h for the product to dry. Treat the surface with fine Troton abrasive fleece, clean and degrease (Silicone Remover Troton).
Information
Anti-slip additive
To obtain an anti-slip coating, use TROTON RANGERS anti-slip powder (10g).
The package contains 10g of anti-slip additive needed to fill one bottle of RANGERS product (1kg/840ml mixture).
Pour the contents directly into the RANGERS bottle, add the hardener and mix thoroughly for about 2 minutes.
The anti-slip coating can be obtained using a UBS or conventional gun. The anti-slip additive can be added to all layers or to the last layer.
Information
RANGERS black HARDENER
ml g ml g
210 263 70 70
315 395 105 105
630 790 210 210
1260 1580 420 420
1890 2370 630 630
UBS Conventional Gun:
Mixing ratio - 3:1
3:1+10÷20%
Nozzle – 1.4÷2.5 mm
Inlet pressure 2÷4 bar 2 bar
Distance 20÷50 cm 20÷50 cm
Number of layers 2 2
Evaporation between layers 30÷50 minutes 30÷50 minutes
Usable hardness 3 days 3 days
Full hardness (severe conditions) 7 days 7 days
Efficiency 2.5÷3 m2 3.5÷6.5 m2
General notes:
Do not exceed the recommended amount of hardener!
The best results are achieved by painting at room temperature.
The ambient temperature and the temperature of the applied product should be similar.
When working with 2-component products, it is recommended to use personal protective equipment. Protect eyes and respiratory tract.
Rooms should be well ventilated.
Tools should be cleaned immediately after application.
Note: For safety, always follow the instructions in the product's MSDS sheet.
